en

CONSTRUCTION SYSTEMS

DECORATIVE FACADE COATINGS BASED MINERAL

ADMIXTURE SYSTEMS

"İzoLatexe Eko" waterproofing material (powder + liquid) 2 bar

"İzoLatexe Eko" waterproofing material (powder + liquid) 2 bar

Product consumption calculator


Preorder


Print


Product description

Composition of powder: Cement based dry mixture resistant to chemicals. Composition of liquid: Acrylic based emulsion polymer. The product conforms to the requirements of the TS AZS 31 43498-05-2005 specifications. For bath-houses, toilet rooms, balconies, and technical water reservoirs.

Fields of Application

This insulating mixture can be applied in the following areas:

  • Permanent water containing reservoirs;
  • Foundations and balconies of buildings;
  • Bearing and dividing walls;
  • Water storage reservoirs;
  • Terraces;
  • Concrete, plaster and flooring plaster surfaces;
  • In the areas of permanent contact with water before application of glazed and mettlach tiles.

Advantages

  • Easy preparation and use;
  • Long usage period;
  • Resistance to chemical substances and salts contained in the soil;
  • Due to high adhesive ability and elasticity the product forms strong waterproofing insulation layer on plaster, flooring plaster and other surfaces before application of facing plates.

Application procedures

Preparation of surface. Clean the surface from any residues deteriorating adhesive force. Pay attention to ensuring rigidity of the surface. In case the surface to be used has any defects, they should be removed using MATON 100 repair mixture. Before application of the product the surface should be primed with BINMADER primer.

Preparation of the mixture. Carefully pour 25 kg powder mix into 10 liters of white liquid composite and mix till it is entirely homogeneous (to prepare the mixture it is recommended to use slow circulation mixer). Wait 3-5 minutes to allow complete mixing of the substances composing the mixture, mix again before application.

Application. Spread the prepared mixture over the surface in two layers using roller or brush. The layers should be applied perpendicular to each other. The time between application of layers may be 5-6 hours, depending on the ambient temperature. To prevent formation of cracks in the corners of the product application area, the oval shape should be given to the corners, and the mixture should be reinforced with mesh. The prepared mixture should be used within 3 hours. Do not use the mixture after expiration of this period.

Recommendations. The surface treated with the mixture should be protected from direct sun rays, precipitations and dust for 48 hours, and the product should not be used in the areas of direct solar radiation. As the product is applied in thin layers, after its application onto the surfaces to be subject to pedestrian flows and vehicles traffic it should be treated with protective facing materials, such as concrete flooring plaster and ceramic tiles. The surfaces should be put into operation or covered with facing plates in at least 1 week after application of the mixture.

Consumption

The İzoLatexe  Eko waterproofing mixture is applied onto the surface in 2 layers.

First layer consumption: 1.2  kg/m2.

Second layer consumption: 1.0  kg/m2.

Shelf Life and Storage Method

The powder composite component can be stored during 12 months packed in original sacks in dry conditions on wooden racks, maximum 10 sacks per rack, and the liquid component can be stored during 12 months in plastic cans placed one upon the other in three layers.

Warnings

  • taking into consideration that it is a cement and acrylic based product containing chemical mixtures, immediately rinse it with large amount of water in case of contact with skin or eyes;
  • do not add any substances not indicated in the application instructions;
  • parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50%+5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

  • information indicated in technical specifications is based on scientific and experimental data;
  • Matanat А company is responsible for the product quality only;
  • with the exception of cases of works executed under the supervision of the company specialists, Мatanat  А company shall not be liable for any problems occuring due to improper use of the product by other persons;
  • the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
  • for technical support and/or more information please do not hesitate to contact the Matanat А company!